Instrumentation and Control Lab
- Home
- Instrumentation and Control Lab
Instrumentation and Control Lab
Instrumentation Lab
1. Displacement measurement using LVDT
- LVDT range ± 10 mm
- Screw Gauge to move the core in LVDT
- AC Signal Source, Phase Sensitive Detector and Instrumentation amplifier
- 3 ½ digit display to view displacement
- Test points to measure the signals
- Legend printed in the PCB and wooden closed cabinet
2. Weight measurement using Load Cell
- Strain gauge based Load Cell to measure up to 5 Kg
- Measurement of strain using DC Bridge method
- Instrumentation amplifier
- 3 ½ digit display to view weight
- Test points to measure the signals
- 10 nos. of weight of 100 gms.
- Legend printed in the PCB and wooden closed cabinet
3. Strain measurement using Strain gauge
- Strain gauge fitted with cantilever beam
- Applying strain using weights in terms of 100 gms.
- Measurement of strain using DC Bridge method
- Instrumentation amplifier
- 3 ½ digit display to view strain
- Test points to measure the signals
- Legend printed in the PCB and wooden closed cabinet
4. Torque measurement using Strain gauge
- Torque Sensor based on strain gauge 1 Kg-m
- 1 meter length rod, weights 1 Kg in terms of 100 gms
- Applying torque at different places
- instrumentation amplifiers
- 3 ½ digit display to display the torque
- Test points to measure the signals
- Legend printed in the PCB and wooden closed cabinet
5. Thermocouple Trainer Kit
- J Type Thermo couple
- High input impedance amplifier
- Cold junction compensation using AD 590 or LM 35
- Amplifier and 3 ½ digit display to view the temperature
- Glass Thermometer
- Legend printed in the PCB and wooden closed cabinet
6. RTD Trainer Kit
- Constant Current Source connected to RTD PT 100
- Zero degree voltage source
- 3 ½ digit display to view the temperature
- Glass Thermometer
- Legend printed in the PCB and wooden closed cabinet
7. Thermistor Trainer Kit
- Disc type Thermistor (NTC) used in a Wheatstone Bridge
- Instrumentation amplifier
- 3 ½ digit display to view the temperature
- Glass Thermometer
- Legend printed in the PCB and wooden closed cabinet
8. Temperature measurement Trainer Kit – 3 transducers
- Temperature measurement Using Iron/Constantan Thermocouple
- with cold junction Compensation, Using RTD and Using Thermistor
- Amplifier, Constant Current Source
- 3 ½ digit display to view the temperature
- Glass Thermometer
- Legend printed in the PCB and wooden closed cabinet
9. Instrumentation Amplifier
- Wheatstone Bridge circuit
- Differential input to the Instrumentation amplifier
- Single ended output
- Gain adjustment resistance
- Necessary test points
- Legend printed in the PCB and wooden closed cabinet
10. Photo Electric Transducer (LDR) Application Kit
%20Application%20Kit.jpg){kind=spacer}
- Provision to wire and test the Photo Electric Relay using LDR
- To wire and test the Solid State relay using Opto Coupler
- Necessary test points
- Legend printed in the PCB and wooden closed cabinet
11. a. Measurement of Speed of a DC Motor with photo electric pick up
- Variable speed arrangement of 24V DC Motor
- Photo electric pick up fitted in the shaft of the motor
- Frequency to voltage converter circuit
- Digital display to display the speed
11. b.Stroboscope to verify the speed Make: HTC make, Model: DT-2229
- Flash range: 50 to 20000 (approx), 10mm LCD display Motor shaft speed measurement range 50 to 20000 (approx)
- Flash adjustment: Course and fine adjustment, 230V AC supply
12. Measurement of water level trainer kit Using Capacitive type transducer
- Sump tank
- Overhead water tank with the provision to measure the level
- Capacitive type transducer to measure the level with voltage output
- Variable water flow rate and provision to discharge the water from the tank
- Panel mounted on MS powder coated stands
13. Measurement of Pressure of air using Bourdon Pressure Transducer
- 2Kg Pressure tank
- Bourdon Strain gauge based Pressure measurement
- Release valve
- Foot pump to give air pressure
14. Measurement of negative pressure of air using Bourdon gauge
- Vacuum pump to create negative pressure less than 70 KPa
- 2 liters pressure tank in which the negative pressure is created
- Bourdon gauge for measuring negative pressure
- Valve to remove –ve pressure
15. Measurement of Water flow using Rotameter
- Sump and water tank
- Variable water flow rate
- Flow measurement using Rotameter
- Panel mounted on MS powder coated stands
16. On / Off Control of Level Process
- Water Tank with sump and Overhead tank model
- Ultra sonic level sensors as input
- Set input for low level and high level
- Microcontroller based
- 12V Water pump to pump water from sump to overhead tank
- 24V Solenoid operated Water tap as output
- 12 V and 24V Power Supply
17. On / Off Control of Pressure Process
- Pressure tank of 2 or 5 litres capacity
- Pressure Sensor / Switch as input
- Solenoid Valve to close or open the compressed air
- Microcontroller based
- FRL, Slide Valve
- Baurdon gauge Pressure display
18. On / Off Control of Temperature Process
- Oven with Electrical Heater
- Thermistor LM 35 to sense the temperature of the oven
- Set temperature Potentiometer
- Temperature set input and Comparator circuit
19. Level process control trainer
- To maintain the level of the water in a overhead tank
- Sump and overhead water tank
- Level measurement of water in the overhead water tank using Pressure sensor
- PID controller
- Level set in the PID controller itself
- Flow control of water using Electrical actuator controlled by PID controller output
- Ball valve to release the water from overhead tank
- Panel mounted on MS powder coated stands
20. Temperature process control trainer
- To maintain the temperature of the water in a overhead tank
- Sump and overhead water tank
- Temperature measurement of water in the overhead water tank using RTD
- PID controller
- Temperature set in the PID controller itself
- Flow control of water using Electrical actuator controlled by PID controller output
- Rotameter to measure the present flow of water
- Ball valve to release the water from overhead tank
- Panel mounted on MS powder coated stands
21. Pressure Process Control Trainer
- To maintain the pressure of air in a pressure tank capacity of 8 litres
- Compressed air supply (0-6 bar)
- Pressure transmitter as sensor fitted in the outlet of the tank
- PID controller
- Pressure set in the PID controller itself
- Flow control of compressed air using Electrical actuator controlled by PID controller output
- Pressure gauge at the input side and output of the process
- Safety valve and air release valve fitted in the tank
- Panel mounted on MS powder coated stands
22. Flow process control trainer
- To maintain the constant flow level of the water in outlet pipe
- Water Sump
- Flow measurement in the outlet pipe using turbine type flow sensor
- Pulses to voltage converter
- PID controller
- Flow set in the PID controller itself
- Flow control of water using Electrical actuator controlled by PID controller output
- Rota meter to measure the current flow
- By pass valve for excess flow from the delivery of the pump
- Panel mounted on MS powder coated stands
Send SMS